Luwa LN-0200 other milk processing equipment
Wentorf bei Hamburg
If you decide to buy equipment at a low price, make sure that you communicate with the real seller. Find out as much information about the owner of the equipment as possible. One way of cheating is to represent yourself as a real company. In case of suspicion, inform us about this for additional control, through the feedback form.
Before you decide to make a purchase, carefully review several sales offers to understand the average cost of your chosen equipment. If the price of the offer you like is much lower than similar offers, think about it. A significant price difference may indicate hidden defects or an attempt by the seller to commit fraudulent acts.
Do not buy products which price is too different from the average price for similar equipment.
Do not give consent to dubious pledges and prepaid goods. In case of doubt, do not be afraid to clarify details, ask for additional photographs and documents for equipment, check the authenticity of documents, ask questions.
The most common type of fraud. Unfair sellers may request a certain amount of advance payment to “book” your right to purchase equipment. Thus, fraudsters can collect a large amount and disappear, no longer get in touch.
- Transfer of prepayment to the card
- Do not make an advance payment without paperwork confirming the process of transferring money, if during the communication the seller is in doubt.
- Transfer to the “Trustee” account
- Such a request should be alarming, most likely you are communicating with a fraudster.
- Transfer to a company account with a similar name
- Be careful, fraudsters may disguise themselves as well-known companies, making minor changes to the name. Do not transfer funds if the company name is in doubt.
- Substitution of own details in the invoice of a real company
- Before making a transfer, make sure that the specified details are correct, and whether they relate to the specified company.
Seller's contacts
Germany, Gifhorn
Germany, Wentorf Bei Hamburg
Germany, Wentorf Bei Hamburg
Germany, Wentorf Bei Hamburg
Germany, Wentorf Bei Hamburg
Germany, Wentorf Bei Hamburg
Germany, Wentorf Bei Hamburg
Germany, Wentorf Bei Hamburg
Germany, Wentorf Bei Hamburg
Germany, Wentorf Bei Hamburg
Germany, Wentorf Bei Hamburg
Germany, Wentorf Bei Hamburg
Germany, Gifhorn
Germany, Gifhorn
Germany, Wentorf Bei Hamburg
Germany, Gifhorn
Germany, Munich
Germany, Gifhorn
Germany, Bielefeld
Germany, Wentorf Bei Hamburg
Product: Dairy products
Heating surface: 21,5 Sq. Ft
Internal volume: 280 Liter
Jacket volume: 26 Liter
Max. Heating Medium Pressure (according ASME U-Stamp): Body: 165 PSIG - 370°F / 120 PSGI - 650°F
Internal pressure: Vacuum up to atmospheric pressure
Rotor speed: 402 rpm
Dimensions: ± 5,5 x 2,0 x 0,6 mtr
Luwa SMS GmbH LN-0200 - Vertical Thin Film Evaporator consist of a cylindrical
vertically-arranged body with heating jacket. A rotor inside the body is equipped with rows of pendulum blades along the full length of the dryer. Special thin-film evaporator designed for dairy service
discharge system
vapor pipe
condenser
and drives. It was in used as a pilot plant on a dairy service until early 2001 and afterwards converted to a 2 square metre cheese base processor with discharge system and ran till 2025 in a Casein plant in a dairy factory in New Zealand.The vertical thin film dryers operate as follows: The wet feed is spread by the pendulum blades in a thin layer onto the heated wall. During this process
the volatile components evaporate continuously out of the product layer at high evaporation rates. The pendulum blades are designed with a minimum gap to the heated wall to prevent fouling deposits on the heating surface
which would reduce performance. The product enters the dryer at the top. Evaporation starts immediately after the boiling point has been reached. First
solids are formed in the slurry zone. The material is then dried to powder under continued shearing by the pendulum blades. The final solid product is discharged by gravity at the bottom of the dryer via a suitable air lock. The operation principle and the design of the vertical thin film dryers offer unique advantages: From liquid to solid in one step
little product hold-up
short residence time
vacuum and atmospheric operation and high performance even with fouling substances. Typical applicatons: drying of salts such as chlorides
bromides
sulphates
carbonates
xanthates
phospates and neutralisation salts
wastewater treatment
silane recovery
silicone drying or glycerine recovery. Heating surface: 21,5 Sq. Ft. Max. Heating Medium Pressure (according ASME U-Stamp): Body: 165 PSIG - 370°F / 120 PSGI - 650°F. Internal pressure: Vacuum up to atmospheric pressure. Product wetted parts: T316L SS or 316 Ti. Volume internal: 280 liter. Volume jacket: 26 Liter. Motor: 75 kW - 415 V - 173 A - 740 rpm - 50 Hz. Bottoms Pump: Allweiler-Seeberg Type SNBP 100.2 VI PI K22 LL 4003 with special auger for product removal from bottom cone.show contacts